How to return the motorcycle brake caliper assembly clearance from the back brake

by:DEFUS     2020-06-19
How to return the motorcycle brake caliper assembly clearance from the back brake. Modern motorcycle, especially large displacement of imported cars, the brake is disc brake firmly held. The advantages of disc brake is self-evident, but after years of development, the braking system of the technology is also in constant innovation. As a result of motorcycle, especially large displacement motorcycle attribute has gradually transferred from vehicle to toys, so the requirement of dynamic system is not only able to endure. In order to make better control of the vehicle the driver, brake system vendor has long moves on to the system control and dynamic. Motorcycle brake caliper assembly how return not place is probably the tubing plugging ~ eighty percent is on the brake pump out ~ what is your car? Really can't change the pump on the ~ after all braking systems about the za elder brothers cycling safety directly. And bearing no problem. Maintenance tips: rectangular rubber sealing ring aging, expand the method to have ability to break down 1 pump ( Brake pliers) , ( On) 2 - Five times the brakes, 5 - when piston out 10mm。 Such as piston is smooth, pressure and back to the difficult consider sealing ring aging, expansion, deformation, etc. 2 continue to grip ( On) The brakes until the brake caliper pistons completely exposed, remove the piston. View the brake clamp cylinder, removal, get out of the cylinder in rectangular rubber sealing ring and clear the crystal of seal ring installation groove. With fine sand paper burnish seal wall, should be like a ground zero. 3 - 0. 7mm。 Three will seal installation groove back, pay attention to not distort. Will touch some hydraulic oil and piston cylinder. If it's difficult, sealing ring and a few burnish. (4) to guide pin point butter or oil, install the brake caliper. 5 slightly loose the exhaust valve on the rear screw, the brake fluid from exhaust valve with a syringe injection, observation window view on the brake pump, the oil to the ceiling above, tighten vent screw, remove the syringe. The advantage is almost no exhaust. 6 consecutive grip ( On) Brake until the brake caliper piston driven friction plate fully contact with the brake disc and powerful, if there is no pressure to the dynamic clamp exhaust system, until there is pressure. Clearance from the back brake clearance from back a caliper assembly, including clamp body, clamp body is equipped with two pieces of brake lining, the clamp body is equipped with braking hydraulic cylinder; Brake hydraulic cylinder including fixed block installed on the clamp body, inside the cylinder body and its sliding fit with the pistons, and has a gap between piston and cylinder since back an agency; Clearance from the back institutions including fixed installation guide bar in the center of the cylinder block, piston sliding fit suit on the guide bar, on the guide bar suit has a limit, limit has adjust the clearance between piston and and limit 座背 to one side of the brake lining between the piston and is equipped with the suit on the guide bar of the side facing the brake lining of pressure springs, and is equipped with the limit between piston structure; On the guide bar also suit sets in the limit, limit of clearance between parts, pressure spring in the clearance at limit seat on both sides. The present invention also made public a clearance from the back brake. Principal right require a clearance from the back a caliper assembly, including clamp body, as described on the clamp body is equipped with two pieces of brake lining, whose character is: described on the clamp body is equipped with brake lining described used to drive two blocks or phase back movement of the brake hydraulic cylinder; Brake hydraulic cylinder including fixed installation in clamp body on the cylinder block, as described within the cylinder body and its sliding fit with the pistons, piston and the corresponding brake lining described described fixed connection, and described with clearance between piston and cylinder since back an agency; Clearance from the back a institutions including fixed installation in the guide bar in the center of the cylinder body, piston sliding fit suit it is stated on the guide bar, described on the guide bar suit has a limit, limit stated has adjust the clearance between the piston and stated, and the limit stated 座背 described to between one side of brake lining and described the piston has set it on the guide bar of the pressure spring, described a side of brake lining and described with limit between piston structure; Described on the guide bar also suit has described with limit limit with the clearance between the adjustable pieces, described in the clearance between the adjustable pieces and described in the guide rod is greater than the static friction force of spring pressure, the limit pressure of work, and described the pressure spring in the mentioned clearance adjustable parts described in both sides of the limit.
Custom message
Contact